Electrical equipment of the car engine Renault Logan 2

Rechargeable battery charging system
Rules for performing work on the battery Attention: Sulfuric acid, found in battery electrolyte, is an extremely corrosive and toxic liquid that is corrosive to most metals. If acid gets on clothing, thoroughly rinse...

Removal and installation of the generator, engine D4F (1.2 l)
Removing the generator 1. Place the vehicle on a two post lift. 2. Disconnect the negative battery terminal. 3. Unscrew the fastening bolts and remove the engine protective tray. 4. Remove the right front wheel from the...

Removal and installation of the generator, K7M engine (1.6 l, 8 valves)
Removing the generator 1. Place the vehicle on a two post lift. 2. Disconnect the negative battery terminal. 3. Remove the right front wheel from the vehicle. 4. Remove the front bumper from the car. 5. Remove...

Removal and installation of the generator, K4M engine (1.6 l, 16 valves)
Removing the generator 1. Place the vehicle on a two post lift. 2. Disconnect the negative battery terminal. 3. Remove the front bumper from the car. 4. Shine Attachment Belt (see chapter " The mechanical part of the...

Removal and installation of the generator, K9K engine (diesel 1.5 l)
Removing the generator 1. Place the vehicle on a two post lift. 2. Disconnect the negative battery terminal. 3. Remove the right front wheel from the vehicle. 4. Remove attachment drive belt (see chapter " The...

Generator repair
Generator check Perform a test of the generator on the stand according to the scheme given above, using: ammeter with scale 0-150 A (for 110 A generator) or ammeter with a scale of 0 - 100 A (for 70 A generator),...

Removal and installation of a starter D4F engine (1.2 l)
Removing the starter 1. Disconnect the negative battery terminal. 2. Remove the air filter unit (see chapter " Intake and exhaust system "). 3. Loosen the nut (1) starter positive terminal. 4. Loosen the nut (2) starter...

Removal and installation of a starter, K7M engine (1.6 l, 8 valves)
Removing the starter 1. Put the car on a two-foot lift. 2. Disconnect the negative battery terminal. 3. Loosen the bolt (2) fastenings of draft of a gear change. Note: The shift rod is connected with a spacer. Be...

Removal and installation of a starter, K4M engine (1.6 l, 16 valves)
Removing the starter 1. Place the vehicle on a two post lift. 2. Disconnect the negative battery terminal. 3. Remove the air resonator (see chapter " Intake and exhaust system "). 4. Move the boot of the gear lever. 5....

Removal and installation of a starter, K9K engine (diesel 1.5 l)
Removing the starter 1. Place the vehicle on a two post lift. 2. Unscrew the fastening bolts and remove the engine protective tray. 3. Disconnect the negative battery terminal. 4. Remove the intercooler outlet (see...

Removal and installation of the ignition coil of the D4F engine (1.2 l)
Removing the ignition coil 1. Disconnect the negative battery terminal. 2. Remove the air filter unit. 3. Disconnect the high voltage wires from the spark plugs. Attention: To disconnect high-voltage wires, it is...

Removal and installation of the ignition coil of the K7M engine (1.6 l, 8 valves)
Removing the ignition coil 1. Disconnect the high voltage spark plug wires from the ignition coil assembly. Attention: To disconnect high-voltage wires, it is forbidden to pull on the wires - pull only on the...

Removal and installation of ignition coils of the K4M engine (1.6 l, 16 valves)
Removing ignition coils 1. Disconnect connectors (1) from ignition coils. 2. Loosen the screws (2) and remove the ignition coils from the engine. Installation of ignition coils Note: Be sure to replace the ignition coil...

Removal and installation of spark plugs, D4F engine (1.2 l)
Removing spark plugs 1. Loosen the bolts (1) air filter unit cover. 2. Remove the cover of the air filter unit with the air intake duct. 3. Disconnect high voltage wires (5) spark plugs. Attention: To disconnect...

Removal and installation of spark plugs, K7M engine (1.6 l, 8 valves)
Removing spark plugs 1. Disconnect the high voltage wires from the spark plugs. Attention: To disconnect high-voltage wires, it is forbidden to pull on the wires - pull only on the connectors. 2. Unscrew the spark plugs...

Removal and installation of spark plugs, K4M engine (1.6 l, 16 valves)
Removing spark plugs 1. Remove the ignition coils from the engine (see above). 2. Unscrew the spark plugs using the wrenches from the kit (Ele. 1382). Installing spark plugs 1. Check and, if necessary, correct the gap...

Diesel engine preheating system
Glow plugs Removal and installation of glow plugs Removing glow plugs 1. Remove the engine cover. 2. Remove the turbocharger outlet pipe. 3. Unhook the protective cover of the fuel rail from the clips (1). 4. Loosen the...

Special tools and fixtures
Name of tool and fixtures Catalog number Set of spark plug wrenches 16 and 21 mm + square adapter 9-9.52 for Ele. 1086 Ele. 1382 14 mm spark plug Ele. 1382-01 torque wrench Ele. 1933